Bitaxe.de
ICE Tower Low Profile

ICE Tower Low Profile Kit

Low-profile cooler with four heatpipes and a 60 mm Noctua for Bitaxe and Nerdaxe

Item no.: 26126 · Manufacturer: Bitaxe.de · Series: Noctua

  • Four copper heatpipes, low-profile build
  • 60 × 15 mm Noctua fan in the set
  • Paste, bracket, pins and Y-splitter included
  • For Bitaxe and Nerdaxe, not for NerdQaxe
4,9 · 51 Reviews
€69.00 incl. VAT

plus shipping · −5% with Bitcoin: €65.55

In stock · ships within 24 h

Free shipping from 200 € Ships within 24 h 14-day right of withdrawal

Product information

ICE Tower Low Profile Kit: maximum cooling headroom for Bitaxe and Nerdaxe

The ICE Tower Low Profile Kit is the top stage of the ICE Tower series. Four copper heatpipes pick the heat up at the ASIC and spread it into a flat, wide fin stack, with a 60 × 15 mm Noctua fan sitting above it.

The difference to the narrow tower design is direction: instead of leading the heat upwards, the low-profile build spreads it across an area and gives the large fan the whole block to work with. Buyers describe exactly that – stronger cooling in a flat build.

Why four heatpipes and a 60 mm fan belong together

  • Four paths instead of two: more heatpipes pull the heat out of the small contact area faster, before it builds up.
  • Large area, large air volume: a 60 mm fan achieves at low speed what a 40 mm fan would have to spin up for.
  • Calm under sustained load: the bigger the buffer, the less often the fan curve steps up.
  • A base for overclocking: more frequency creates more heat – this kit is built for that.

Building flat means building wider

The kit gets its performance from area, not height. The block sits low but reaches further beyond the board than the stock cooling. In an open build that is no problem; in a tight niche or a closed case you should measure first. One customer put it neatly: technically too big – but it works.

Compatibility: Bitaxe and Nerdaxe

The kit fits Bitaxe and Nerdaxe boards, for example the Bitaxe Gamma or the Nerdaxe Gamma. It does not fit:

  • NerdQaxe models – confirmed by feedback from people who tried
  • NerdOctaxe models

Who the Low Profile Kit is for

For users who run their board under permanent load, adjust frequency and voltage or work in a warm room. The kit provides the necessary buffer.

It is overkill if your miner runs at factory settings and should sit unobtrusively on a shelf. The smaller ICE Tower Kit is enough for that.

What you need to fit it

Everything necessary is included: heatsink, 60 mm Noctua, ASIC bracket with a 4-pin mount, thermal paste, four mounting pins and the Y-splitter cable. Clean the contact surface before the swap and seat the block evenly – afterwards compare temperature and fan speed with the values from before. If you are setting the miner up again, the setup guide helps.

Accessories and sensible upgrades

  • Noctua NF-A6x15 as a replacement or second 60 mm fan on the Y-splitter.
  • Copper heatsinks for the voltage regulators, which also warm up when overclocking.

Ready to get your Bitaxe under control?

If your board reaches the temperature limit under load, the ICE Tower Low Profile Kit is the most consistent answer for Bitaxe and Nerdaxe: four heatpipes, a large fan and all the mounting hardware in one package.

Frequently asked questions about the ICE Tower Low Profile Kit

Does the Low Profile Kit fit the Bitaxe Gamma?

Yes. The kit is designed for Bitaxe and Nerdaxe boards, and the Bitaxe Gamma is one of them. It also seats correctly on the Nerdaxe Gamma – putting that device into operation is described in the Nerdaxe Gamma setup guide.

Does it fit the NerdQaxe or the NerdOctaxe?

No. The kit is not suitable for the NerdQaxe++ or the NerdOctaxe – as customers who tried it there also report.

What is the difference to the regular ICE Tower Kit?

Four copper heatpipes instead of a narrow tower, and a 60 × 15 mm Noctua instead of the 40 mm fan, at a higher price. If you do not overclock, the ICE Tower Kit is usually enough.

How much space does the cooler need?

It builds flat but reaches wider over the board than the stock cooling. In an open build that is no issue; in a tight case you should measure beforehand.

Is the fan controlled by the board?

Yes. The Noctua connects to the 4-pin mount and follows your board’s PWM fan curve; the included Y-splitter cable allows a second fan on the same header.

Is thermal paste included?

Yes. Thermal paste, ASIC bracket, four mounting pins and the Y-splitter cable are included – nothing to buy on top.

Is the kit worth it if I do not overclock?

Only to a degree. Without overclocking the gain is smaller than the price difference suggests. It becomes worthwhile with permanently high load, warm rooms or when you raise frequency and voltage.

Can I use a different 60 mm fan?

Yes, as long as it measures 60 mm and has a PWM connector. A suitable replacement is the Noctua NF-A6x15.

Is the 60 mm fan quieter than a 40 mm fan?

At the same cooling performance, usually yes: the larger fan moves the same volume of air with fewer revolutions. We do not quote numbers, because room, location and fan curve determine the result.

What is the difference to the AXP60 Copper Pro?

The AXP60 Copper Pro relies on 210 g of copper mass with two heatpipes and fits the Bitaxe Gamma and Nerdaxe Gaia. The Low Profile Kit works with four heatpipes, is designed as a complete set and fits Bitaxe as well as Nerdaxe.

Does the cooler lower the error rate in the firmware?

Not automatically. Excessive temperatures can drive error counts up, but they are only one of several causes – power supply and pool settings are worth checking too.

How involved is the swap?

Manageable: old heatsink off, clean the surface, apply paste, fix the block with the four pins, plug in the fan. Nothing is soldered – still, take a few quiet minutes so the block sits evenly.

Why buy from Bitaxe.de?

Free shipping from 200 €

Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.

Truly open source

Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.

CE, warranty & returns

Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.

Direct support

Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.

Customer reviews

4.9 / 5 · 51 reviews from customers who bought this product from us.

All reviews
06.10.2026
Cant hear my Gamma anymore, brilliant!
Gareth Verified purchase
05.10.2026
Am Wochenende auf den Nerdaxe Gamma gebaut. Hab etwas Respekt davor gehabt, war aber harmlos: Paste draufgetupft, Block mit den vier Pins festgedrückt, Lüfter in die Buchse. Womit ich nicht gerechnet habe: Die vier Heatpipes sind nicht nur Deko, der Chip liegt jetzt ein ganzes Stück unter dem alten Wert und der große Noctua dreht so gemütlich, dass ich erst dachte, er steht. Nach drei Tagen noch kein Langzeiturteil, aber der Sohnemann hat gefragt, ob der überhaupt noch an ist.
Burkhard Verified purchase
24.09.2026
Block sticks out past the board, and the paste barely covers one try. Four heat pipes let me nudge the Gamma up a notch with the fan staying quiet.
Oscar Verified purchase
23.09.2026
Na Gammě běží dva týdny místo sériového chladiče. Teplota čipu šla při stejné frekvenci znatelně dolů a ventilátor se drží hluboko pod tím, kde dřív jela původní čtyřicítka. Díky tomu jsem zvedl frekvenci, teď se držím kolem 1,45 TH/s a čip zůstává s rezervou pod hranicí, kterou si hlídám. Montáž bez pájení, pasta byla v balení a starý chladič jsem si nechal do šuplíku jako rezervu.
Martin Verified purchase
17.09.2026
Ordered on a Thursday evening, which I assumed meant nothing would happen before the following week. Instead the shipping confirmation with a tracking number arrived Friday around noon and the parcel was at my door on Monday, quicker than most things I order. Packaging was sensible rather than fancy: a small cardboard box, the heatsink wrapped separately, the fan in its own box, and a little bag with the pins, the paste syringe and the splitter cable. Nothing rattled, nothing bent. The invoice was in the box and also came by e-mail, which I appreciated because I never find paper invoices again. As for the kit itself, it has only been on my Gamma since Monday night, so I will not pretend to know how it behaves over months. Fitting took longer than the few minutes people talk about because I was nervous about pressing on the board, but the pins clicked in and the fan went straight onto the header. Early days, but it runs and I did not break anything, which for me counts as a success.
Matt Verified purchase
14.09.2026
Ten minutes with the pins, and the four heat pipes hold my Gamma under target at a duty I barely hear. The fin block overhangs the PCB, measure first.
Kristaps Verified purchase
Show all 51 reviews

Related guides

Setup, pool, cooling, power supply and sensible upgrades for your setup.

You might also like

ICE Tower Low Profile Kit

€69.00