Bitaxe.de
ICE Tower Kit

ICE Tower Kit

Complete tower cooler set with a 40 mm Noctua for Bitaxe and Nerdaxe

Item no.: 91832 · Manufacturer: Bitaxe.de

  • ICE Tower heatsink with a 40 mm Noctua
  • Bracket, paste, pins and Y-splitter included
  • For Bitaxe and Nerdaxe, not for NerdQaxe
  • Fits without soldering or special tools
5,0 · 60 Reviews
€49.00 incl. VAT

plus shipping · −5% with Bitcoin: €46.55

In stock · ships within 24 h

Free shipping from 200 € Ships within 24 h 14-day right of withdrawal

Product information

ICE Tower Kit: tower cooler with a Noctua fan for Bitaxe and Nerdaxe

The ICE Tower Kit is a complete cooling upgrade: tower heatsink, 40 mm Noctua fan, 3D-printed ASIC bracket with a 4-pin mount, thermal paste, four mounting pins and a PWM Y-splitter cable. You unpack it, swap it over and you are done – without a missing part halfway through.

The tower gives the ASIC considerably more surface than the stock cooling. The same heat spreads across more fins, so the fan has less work to do. That is exactly what buyers describe: better cooling and quieter than before.

Why the ICE Tower Kit is worth it

  • Complete instead of a parts hunt: paste, bracket, pins and Y-splitter are included – no second order.
  • Noctua instead of a bundled fan: the 40 mm fan runs quietly and still follows your board’s fan curve.
  • More even temperatures: more mass dampens the swings between idle and full load.
  • Headroom above: if you want to overclock moderately, this provides the thermal buffer for it.

What the Y-splitter in the kit does

The board usually has one fan header. The included PWM Y-splitter cable divides it so you can run two fans – for example the Noctua on the tower and a second one for airflow in the case. Control stays with the board: both follow the same curve.

Compatibility: Bitaxe and Nerdaxe

The kit is intended for Bitaxe and Nerdaxe models, for example the Bitaxe Gamma. It does not fit:

  • NerdQaxe models such as the NerdQaxe++
  • NerdOctaxe models

Check which board you run before ordering.

Who the ICE Tower Kit is for

For everyone whose miner lives in a living room and who wants it cooler and quieter without collecting the parts individually. The tower builds upwards, so the footprint stays narrow.

It is less of a fit if you are after maximum headroom for permanent overclocking – then the ICE Tower Low Profile kit is the more consistent choice. If only the fan noise bothers you, swapping the fan alone is often enough.

What you need to fit it

Nothing beyond the kit: thermal paste, bracket and fasteners are included. Clean the contact surface before applying the paste and make sure the heatsink sits flat. Once the miner is back online, compare temperature and fan speed in the dashboard with the values from before. If you are setting it up again from scratch, the setup guide walks you through the steps.

Accessories and sensible upgrades

  • Noctua NF-A4x20 as a second 40 mm fan on the Y-splitter or as a replacement.
  • Copper heatsinks for the voltage regulators the tower cooler does not cover.
  • Cooling with all the other parts around airflow and temperature.

Ready for a cooler and quieter setup?

The ICE Tower Kit is the most straightforward cooling upgrade for Bitaxe and Nerdaxe: one package, one swap, and afterwards lower temperatures and a fan that spins up less often.

Frequently asked questions about the ICE Tower Kit

Does the ICE Tower Kit fit the Bitaxe Gamma?

Yes. The kit is designed for Bitaxe and Nerdaxe models, and the Bitaxe Gamma is one of them.

Does the kit fit the NerdQaxe++ or the NerdOctaxe?

No. This cooling upgrade is not suitable for the NerdQaxe++ or the NerdOctaxe.

Is thermal paste included?

Yes. Thermal paste, the 3D-printed ASIC bracket with a 4-pin mount, four mounting pins and a PWM Y-splitter cable all come with the kit.

Do I need extra screws or tools?

No. The four mounting pins are included, and nothing has to be soldered or drilled.

What is the Y-splitter cable for?

It lets you run two fans from one fan header on the board. Both then follow the same PWM control.

Does the kit make the miner quieter?

Usually yes. The larger cooling surface and the Noctua fan mean a lower speed is enough for the same load. We do not quote specific dB figures, because location and fan curve strongly influence the result.

What is the difference to the ICE Tower Low Profile kit?

The ICE Tower Kit works with the 40 mm Noctua. The ICE Tower Low Profile kit has four copper heatpipes and a 60 × 15 mm Noctua – more headroom, but a flatter and wider build.

What is the difference to a single Noctua fan?

A Noctua NF-A4x20 only replaces the fan. The kit replaces the entire heatsink and brings the fan with it – so the difference in temperature is correspondingly larger.

Can I overclock after fitting it?

Yes, moderately. The additional thermal buffer is there for exactly that. Move in small steps and watch the temperature after every change.

Does better cooling help against high error rates?

Sometimes: excessive ASIC temperatures are one possible cause of rising error counts. There are other reasons too, so check power supply and pool settings as well.

Does the kit also fit a Nerdaxe?

Yes, Nerdaxe boards are explicitly covered. How to put such a device into operation is described in the Nerdaxe Gamma setup guide.

Does the kit cool the voltage regulators too?

No, the tower cooler sits on the ASIC. For the other hotspots on the board there are the small copper heatsinks.

Why buy from Bitaxe.de?

Free shipping from 200 €

Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.

Truly open source

Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.

CE, warranty & returns

Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.

Direct support

Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.

Customer reviews

5.0 / 5 · 60 reviews from customers who bought this product from us.

All reviews
16.08.2026
On the Gamma since April and still cool.
Mindaugas Verified purchase
15.08.2026
Bestellt am Donnerstag, Samstag war es da, Sonntag umgebaut. Die gedruckte Halterung passt sauber um den Chip, Paste liegt bei, die vier Pins sitzen nach einem kräftigen Druck, Werkzeug braucht man keins. Chiptemperatur am Gamma bei 525 MHz von 58 auf 44 Grad, der Noctua ist im Wohnzimmer nicht mehr rauszuhören. Nicht bedacht hatte ich die Höhe: In das Regalfach von vorher passt der Gamma mit Turm nicht mehr, jetzt steht er auf dem Sideboard.
Noah Verified purchase
24.07.2026
Übertaktet und trotzdem schön kühl, Halterung sitzt stramm!
Frank Verified purchase
23.07.2026
Na vier maanden durf ik het wel te zeggen: dit was de beste aankoop na de miner zelf. Mijn Gamma was mijn eerste miner en in het begin stond hij op de kast in de woonkamer te zoemen als een oude laptop die het zwaar heeft, vooral 's avonds als het stil werd. Met de toren is de chiptemperatuur in het dashboard van rond de 63 graden naar 47 gezakt en de ventilator draait zo rustig dat ik 's avonds de koelkast in de keuken eerder hoor dan de miner. De koelpasta zat gewoon in het doosje, dus ik hoefde niets apart te bestellen, en er was zelfs genoeg over voor een tweede poging toen ik de koeler de eerste keer iets scheef had gezet. Voor iemand zonder enige ervaring met hardware was het montagegedeelte spannender dan het hoefde te zijn, maar het is echt niet meer dan oude koeler eraf, schoonmaken, pasta erop, toren erop, vier pinnetjes erdoor. Sinds de ombouw kijk ik eigenlijk alleen nog op het dashboard om te zien of de hashrate er nog staat. Mijn zoontje noemt het ding nu de wolkenkrabber!
Thijs Verified purchase
22.07.2026
Ordered on a Sunday evening, shipping notice from the shop on Monday, parcel on the doormat in the Netherlands on Wednesday, so the mood was already good before I opened the box. And then the tower itself: I did not expect to care about how a heatsink looks, but this thing turns the Gamma from a bare circuit board into something that looks like a tiny PC build. The copper heatpipe, the stacked fins, the beige-and-brown Noctua on top, it just looks deliberate. It now stands on my desk next to the monitor instead of hiding behind it, and two colleagues on a video call asked what the mini tower was. Function-wise the numbers are nice too: chip went from the high 50s to around 45 degrees at stock clock and the Noctua idles so low I have to put a finger near it to feel it spinning. Mounting was ten minutes with the printed bracket and the pins. Thirty days in, and the stock cooler is in a drawer where it belongs.
Sem Verified purchase
07.07.2026
Paste and splitter included, still hear it tho.
Jakub Verified purchase
Show all 60 reviews

Related guides

Setup, pool, cooling, power supply and sensible upgrades for your setup.

You might also like

ICE Tower Kit

€49.00