Bitaxe.de
ICE Tower Low Profile

ICE Tower Low Profile Kit

Low-profile cooler with four heatpipes and a 60 mm Noctua for Bitaxe and Nerdaxe

Item no.: 26126 · Manufacturer: Bitaxe.de · Series: Noctua

  • Four copper heatpipes, low-profile build
  • 60 × 15 mm Noctua fan in the set
  • Paste, bracket, pins and Y-splitter included
  • For Bitaxe and Nerdaxe, not for NerdQaxe
4,9 · 51 Reviews
€69.00 incl. VAT

plus shipping · −5% with Bitcoin: €65.55

In stock · ships within 24 h

Free shipping from 200 € Ships within 24 h 14-day right of withdrawal

Product information

ICE Tower Low Profile Kit: maximum cooling headroom for Bitaxe and Nerdaxe

The ICE Tower Low Profile Kit is the top stage of the ICE Tower series. Four copper heatpipes pick the heat up at the ASIC and spread it into a flat, wide fin stack, with a 60 × 15 mm Noctua fan sitting above it.

The difference to the narrow tower design is direction: instead of leading the heat upwards, the low-profile build spreads it across an area and gives the large fan the whole block to work with. Buyers describe exactly that – stronger cooling in a flat build.

Why four heatpipes and a 60 mm fan belong together

  • Four paths instead of two: more heatpipes pull the heat out of the small contact area faster, before it builds up.
  • Large area, large air volume: a 60 mm fan achieves at low speed what a 40 mm fan would have to spin up for.
  • Calm under sustained load: the bigger the buffer, the less often the fan curve steps up.
  • A base for overclocking: more frequency creates more heat – this kit is built for that.

Building flat means building wider

The kit gets its performance from area, not height. The block sits low but reaches further beyond the board than the stock cooling. In an open build that is no problem; in a tight niche or a closed case you should measure first. One customer put it neatly: technically too big – but it works.

Compatibility: Bitaxe and Nerdaxe

The kit fits Bitaxe and Nerdaxe boards, for example the Bitaxe Gamma or the Nerdaxe Gamma. It does not fit:

  • NerdQaxe models – confirmed by feedback from people who tried
  • NerdOctaxe models

Who the Low Profile Kit is for

For users who run their board under permanent load, adjust frequency and voltage or work in a warm room. The kit provides the necessary buffer.

It is overkill if your miner runs at factory settings and should sit unobtrusively on a shelf. The smaller ICE Tower Kit is enough for that.

What you need to fit it

Everything necessary is included: heatsink, 60 mm Noctua, ASIC bracket with a 4-pin mount, thermal paste, four mounting pins and the Y-splitter cable. Clean the contact surface before the swap and seat the block evenly – afterwards compare temperature and fan speed with the values from before. If you are setting the miner up again, the setup guide helps.

Accessories and sensible upgrades

  • Noctua NF-A6x15 as a replacement or second 60 mm fan on the Y-splitter.
  • Copper heatsinks for the voltage regulators, which also warm up when overclocking.

Ready to get your Bitaxe under control?

If your board reaches the temperature limit under load, the ICE Tower Low Profile Kit is the most consistent answer for Bitaxe and Nerdaxe: four heatpipes, a large fan and all the mounting hardware in one package.

Frequently asked questions about the ICE Tower Low Profile Kit

Does the Low Profile Kit fit the Bitaxe Gamma?

Yes. The kit is designed for Bitaxe and Nerdaxe boards, and the Bitaxe Gamma is one of them. It also seats correctly on the Nerdaxe Gamma – putting that device into operation is described in the Nerdaxe Gamma setup guide.

Does it fit the NerdQaxe or the NerdOctaxe?

No. The kit is not suitable for the NerdQaxe++ or the NerdOctaxe – as customers who tried it there also report.

What is the difference to the regular ICE Tower Kit?

Four copper heatpipes instead of a narrow tower, and a 60 × 15 mm Noctua instead of the 40 mm fan, at a higher price. If you do not overclock, the ICE Tower Kit is usually enough.

How much space does the cooler need?

It builds flat but reaches wider over the board than the stock cooling. In an open build that is no issue; in a tight case you should measure beforehand.

Is the fan controlled by the board?

Yes. The Noctua connects to the 4-pin mount and follows your board’s PWM fan curve; the included Y-splitter cable allows a second fan on the same header.

Is thermal paste included?

Yes. Thermal paste, ASIC bracket, four mounting pins and the Y-splitter cable are included – nothing to buy on top.

Is the kit worth it if I do not overclock?

Only to a degree. Without overclocking the gain is smaller than the price difference suggests. It becomes worthwhile with permanently high load, warm rooms or when you raise frequency and voltage.

Can I use a different 60 mm fan?

Yes, as long as it measures 60 mm and has a PWM connector. A suitable replacement is the Noctua NF-A6x15.

Is the 60 mm fan quieter than a 40 mm fan?

At the same cooling performance, usually yes: the larger fan moves the same volume of air with fewer revolutions. We do not quote numbers, because room, location and fan curve determine the result.

What is the difference to the AXP60 Copper Pro?

The AXP60 Copper Pro relies on 210 g of copper mass with two heatpipes and fits the Bitaxe Gamma and Nerdaxe Gaia. The Low Profile Kit works with four heatpipes, is designed as a complete set and fits Bitaxe as well as Nerdaxe.

Does the cooler lower the error rate in the firmware?

Not automatically. Excessive temperatures can drive error counts up, but they are only one of several causes – power supply and pool settings are worth checking too.

How involved is the swap?

Manageable: old heatsink off, clean the surface, apply paste, fix the block with the four pins, plug in the fan. Nothing is soldered – still, take a few quiet minutes so the block sits evenly.

Why buy from Bitaxe.de?

Free shipping from 200 €

Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.

Truly open source

Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.

CE, warranty & returns

Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.

Direct support

Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.

Customer reviews

4.9 / 5 · 51 reviews from customers who bought this product from us.

All reviews
06.10.2026
Cant hear my Gamma anymore, brilliant!
Gareth Verified purchase
05.10.2026
Am Wochenende auf den Nerdaxe Gamma gebaut. Hab etwas Respekt davor gehabt, war aber harmlos: Paste draufgetupft, Block mit den vier Pins festgedrückt, Lüfter in die Buchse. Womit ich nicht gerechnet habe: Die vier Heatpipes sind nicht nur Deko, der Chip liegt jetzt ein ganzes Stück unter dem alten Wert und der große Noctua dreht so gemütlich, dass ich erst dachte, er steht. Nach drei Tagen noch kein Langzeiturteil, aber der Sohnemann hat gefragt, ob der überhaupt noch an ist.
Burkhard Verified purchase
24.09.2026
Block sticks out past the board, and the paste barely covers one try. Four heat pipes let me nudge the Gamma up a notch with the fan staying quiet.
Oscar Verified purchase
23.09.2026
Na Gammě běží dva týdny místo sériového chladiče. Teplota čipu šla při stejné frekvenci znatelně dolů a ventilátor se drží hluboko pod tím, kde dřív jela původní čtyřicítka. Díky tomu jsem zvedl frekvenci, teď se držím kolem 1,45 TH/s a čip zůstává s rezervou pod hranicí, kterou si hlídám. Montáž bez pájení, pasta byla v balení a starý chladič jsem si nechal do šuplíku jako rezervu.
Martin Verified purchase
17.09.2026
Ordered on a Thursday evening, which I assumed meant nothing would happen before the following week. Instead the shipping confirmation with a tracking number arrived Friday around noon and the parcel was at my door on Monday, quicker than most things I order. Packaging was sensible rather than fancy: a small cardboard box, the heatsink wrapped separately, the fan in its own box, and a little bag with the pins, the paste syringe and the splitter cable. Nothing rattled, nothing bent. The invoice was in the box and also came by e-mail, which I appreciated because I never find paper invoices again. As for the kit itself, it has only been on my Gamma since Monday night, so I will not pretend to know how it behaves over months. Fitting took longer than the few minutes people talk about because I was nervous about pressing on the board, but the pins clicked in and the fan went straight onto the header. Early days, but it runs and I did not break anything, which for me counts as a success.
Matt Verified purchase
14.09.2026
Ten minutes with the pins, and the four heat pipes hold my Gamma under target at a duty I barely hear. The fin block overhangs the PCB, measure first.
Kristaps Verified purchase
13.09.2026
kleiner nachteil vorweg: das ding ist breiter als die platine. mein gamma stand bisher in einer nische im wohnzimmerschrank und da passt er mit dem neuen block jetzt nicht mehr rein, weil der an beiden seiten über den rand hinausgeht. jetzt steht er auf dem sideboard, meine frau findet das weniger lustig als ich. ansonsten bin ich als anfänger ganz gut klargekommen. alten kühler ab, paste drauf, pins durch, lüfter an den stecker, hat vielleicht eine viertelstunde gedauert mit nachlesen. danach hab ich zum ersten mal am takt gedreht und mich dabei an die werte aus dem overclocking-ratgeber gehalten. die anzeige steht jetzt irgendwo um 1,4 th/s und die temperatur ist trotzdem niedriger als vorher mit dem originalen lüfter auf stock. nach drei wochen jedenfalls kein absturz, und man hört den noctua erst, wenn man direkt davor sitzt. ob sich das rechnet, keine ahnung, es ist ja eher ein hobby.
Burkhard Verified purchase
21.08.2026
My Gamma used to announce itself every evening from next to the sofa, and that is over! Four copper pipes into a flat block with that beige Noctua on top looks odd for a day and then you stop noticing it, mostly because you stop hearing it. The temperature in the dashboard dropped so far I thought the reading was broken. It is flat but wider than the board, so instead of the bookshelf it now sits on the windowsill, and nobody here minds.
Yara Verified purchase
17.05.2026
Drei Tage drauf, also erst ein Zwischenstand. Montage unspektakulär: Paste, Block gleichmäßig andrücken, Lüfter anstecken. Bei 600 MHz und 1150 mV liegt der Chip jetzt klar unter der Marke, bei der ich vorher den Lüfter auf Anschlag hatte, der Noctua läuft dabei weit unten in der Kurve. Was mich stört, ist der Preis: für Kühlkörper, Lüfter und etwas Kleinkram ist das happig, der kleine ICE Tower hätte für Stock-Takt wohl gereicht. Und der Block ragt deutlich über die Platine, für ein geschlossenes Gehäuse ist das nichts.
Henrik Verified purchase
08.05.2026
Seit Januar auf meinem Gamma und ich will den alten Kühler nicht mehr sehen. Die Temperatur am Chip ist bei gleicher Frequenz spürbar runtergegangen und der Lüfter dreht gefühlt nur noch halb so hoch. Direkt daneben steht noch mein alter Bitaxe Ultra mit seinem 40er Lüfter und der klingt dagegen wie ein kleiner Föhn. Flach stimmt aber er steht seitlich ein gutes Stück über die Platine was auf dem Schreibtisch völlig egal ist und sogar ganz schick aussieht.
Rainer Verified purchase
05.05.2026
Sonntag bestellt Dienstag schon auf dem Gamma!
Adrian Verified purchase
01.04.2026
bumped the clock a bit, temps still boring
Kristaps Verified purchase
28.02.2026
Twee weken op een Gamma 601, daarvoor zat de stockkoeler erop. Vier heatpipes op zo'n klein contactvlak leek me overdreven, maar met dezelfde target van 60 graden draait de Noctua nu een stuk lager in duty dan het 40 mm fannetje ooit deed. Daardoor had ik ruimte om een preset omhoog te gaan, rond 1,4 TH/s blijft de chip ruim onder de 65 die ik mezelf als grens stel. Montage zonder solderen, paste zat erbij, Y-splitter ligt nog in de doos.
Luuk Verified purchase
23.02.2026
also, erstmal: die pins. wer sich die ausgedacht hat, hatte offenbar drei hände. man drückt zwei rein, der block kippelt, der dritte will nicht, und beim vierten springt der erste wieder raus. nach dem zweiten anlauf saß er dann gleichmäßig, aber ich habe zwischendurch wirklich überlegt, den alten kühler wieder draufzusetzen. die anleitung dazu ist auch eher knapp, ein paar bilder mehr hätten nicht geschadet. dann das maß: flach ja, aber der block hängt links und rechts deutlich über die platine raus. in meinem regalfach war das knapp, zwei zentimeter weniger platz und es hätte nicht gepasst. wenn man das vorher weiß, ist es kein problem, ich wusste es nicht. jetzt läuft er seit gut einer woche, der lüfter ist aus einem meter kaum zu hören und die chiptemperatur steht deutlich tiefer als mit dem serienkühler. bewertet habe ich das ergebnis, nicht den einbau.
Jörg Verified purchase
17.02.2026
Bestellt am Mittwochabend, die Versandbestätigung kam Donnerstag, am Samstag stand das Paket vor der Tür. Der Karton ist kleiner als gedacht, innen alles ordentlich in Tütchen sortiert, der Lüfter extra gepolstert, nichts verbogen. Eine Frage per Mail vorab, ob das Kit auch auf meinen Gamma passt, wurde noch am selben Abend beantwortet. Seit zehn Tagen sitzt es nun drauf, der Gamma ist mein erster Miner und ans Übertakten traue ich mich erst, wenn ich mich etwas mehr eingelesen habe.
Jochen Verified purchase
10.02.2026
Four heatpipes, wow, my Bitaxe finally stays cool
Matej Verified purchase
28.01.2026
Eine Anleitung lag bei mir nicht im Karton, den Umbau reimt man sich selbst zusammen. Klappt zwar, Gamma läuft merklich kühler, aber ein Zettel mit drei Bildern wäre kein Hexenwerk.
Luis Verified purchase
25.01.2026
Montaggio lineare: via il dissipatore originale, pulizia del chip, una goccia di pasta, i quattro pin a molla, ventola sul connettore 4 pin. Le quattro heatpipe in rame portano il calore su un blocco di alette largo e piatto, sotto carico tiepido su tutta la superficie. Con lo stesso target di temperatura in AxeOS la Noctua da 60 mm gira a una percentuale molto più bassa e il Gamma regge un gradino di frequenza in più. Prossimo passo, seconda ventola sullo splitter a Y incluso.
Giuseppe Verified purchase
25.01.2026
Den 60er Noctua höre ich mit Standard-Lüfterkurve neben dem Router nicht raus, der alte 40er musste ordentlich drehen. Montage in zehn Minuten: Pins rein, Lüfter an den Header, fertig.
Jannik Verified purchase
24.01.2026
Kam schneller als meine Lust zum Umbauen, lag erst eine Woche im Karton. Sitzt jetzt wie ein zu großer Hut auf der Platine, dafür drehe ich endlich an der Frequenz.
Florian Verified purchase
22.01.2026
Seit drei Tagen drauf, also nur ein erster Eindruck. Die vier Heatpipes holen die Wärme vom BM1370 nach außen in einen flachen Lamellenblock, der fast die ganze Platine überdeckt, entsprechend wenig muss der große Noctua dafür arbeiten. In AxeOS bin ich von 490 auf 590 MHz bei 1150 mV gegangen, die Chiptemperatur liegt trotzdem ein paar Grad unter meinen alten Stock-Werten und der Lüfter pendelt bei einer Zieltemperatur von 62 Grad knapp über der eingestellten Mindestdrehzahl. Fehlerquote und Langzeitwerte folgen in ein paar Wochen.
Bastian Verified purchase
21.01.2026
Zwischen den Jahren bestellt, drei Tage später an der Tür. Wärmeleitpaste eher sparsam bemessen, dafür läuft der Gamma spürbar kühler, auch wenn der Block gut über die Platine hinaussteht.
Ben Verified purchase
20.01.2026
llegó a sevilla en cuatro días y lleva dos meses en mi gamma, chip bastante más fresco y el ventilador a menos vueltas, eso sí la pasta térmica viene justita.
Jaime Verified purchase
07.01.2026
Sechs Monate sind rum, also mal ein Zwischenstand. Gekauft hab ich das Kit im Juli, weil mein Gamma im Schlafzimmer steht und der kleine Originallüfter mich nachts genervt hat, kühler sollte er natürlich auch werden. Der Umbau war einfacher als gedacht: alter Kühler ab, Chip mit Alkohol sauber gemacht, Paste drauf, die vier Pins reingedrückt (beim letzten hab ich kurz geflucht, dann saß er) und den Lüfter angesteckt. Was mich bis heute fasziniert, sind die vier Kupferröhrchen, die laufen vom Chip weg nach außen in den Kühlblock und der ganze Block wird überall gleich handwarm, während die Platine kühl bleibt. Der Noctua dreht so langsam, dass ich anfangs nachts aufgestanden bin, um zu schauen, ob er überhaupt läuft. Zur Größe: flach ja, aber der Kühler ragt links wie rechts über die Platine, mein alter Platz im Bücherregal hat sich damit erledigt. Jetzt steht der Gamma auf einem eigenen Brett an der Wand, sieht mit dem beigen Noctua-Rahmen ein bisschen nach Werkstatt aus, und mir gefällt das sogar besser so.
Milan Verified purchase
04.01.2026
Nicht ganz billig für ein Stück Metall mit Lüfter, aber der Umbau hat am zweiten Weihnachtstag sogar bei mir als Anfängerin geklapt und seit dem ist Ruhe im Arbeitszimmer.
Yvonne Verified purchase
03.01.2026
Vorweg das Nervige: die vier Pins. Man drückt sie durch Platine und Halterung und hofft, dass sie einrasten, bei mir hat der dritte erst im fünften Anlauf geklickt und ich hatte die ganze Zeit Angst, zu fest auf die Platine zu drücken. Deshalb nicht die volle Begeisterung, denn sonst gibt es wenig zu motzen. Das Kit sitzt seit Juli auf meinem Gamma im Dachgeschoss und hat die Hitze im Sommer ohne Überhitzungsmeldung durchgehalten, mit dem Serienkühler hatte er sich im Juni zweimal abgeschaltet. Im Herbst hab ich mich dann getraut, in AxeOS eine Stufe höher zu gehen, erst 550, dann 575 MHz, und der Chip bleibt trotzdem unter meinem Zielwert. Die Hashrate steht jetzt meistens um 1,3 statt knapp 1,2, für mich als Anfänger ein schönes Gefühl. Zum Platz: der Kühler ist niedrig, dafür hängt er auf beiden Seiten über das Board, in meinem offenen Aufbau kein Thema, im Gehäuse wäre es eng geworden. Tipp fürs Montieren: die Pins über Kreuz eindrücken, nicht der Reihe nach, dann liegt der Block gleichmäßig auf.
Ansgar Verified purchase
26.12.2025
Sticks out over the board more than I expected... but my Bitaxe runs way cooler and I don't hear the fan anymore, so no regrets.
Marcos Verified purchase
01.12.2025
Ich bin ja eher der Typ, der am Computer höchstens den Staub rausbläst, trotzdem hab ich mich an den Tausch getraut. Mein Bitaxe steht im Wohnzimmer auf der Kommode und ist, seit wir heizen, ziemlich warm geworden, dazu hat der kleine Serienlüfter gesurrt wie ein Mückenschwarm. Ausgepackt hab ich dann einen Kühler, der aussieht wie aus einem richtigen PC: vier Kupferrohre, die vom Chip weg in einen breiten Rippenblock laufen, obendrauf der braune Noctua. Der alte Kühlkörper wirkt daneben wie ein Spielzeug. Mein Bub hat beim Wechsel die Pins gehalten, viel mehr war da auch nicht zu tun. Das Ding ist zwar flach, aber deutlich breiter als die Platine selbst, das Bild daneben musste weichen. Seit zwei Wochen ist der Bitaxe fühlbar kühler und ich hör ihn vom Sofa aus nicht mehr. Der Bub meint, jetzt schaut er endlich aus wie ein echter Computer.
Alois Verified purchase
24.11.2025
Mein erster Miner, ein Nerdaxe Gamma. Im Spätsommer wurde er mir zu warm, der kleine Lüfter war dauernd zu hören. Also dieses Kit drauf, nach einer Viertelstunde war alles montiert. Flach ist der Kühler, aber rechts und links steht er ein gutes Stück über die Platine, am Schreibtisch egal. Seit sechs Wochen deutlich kühler, ich schaue nicht mehr jede Stunde in die Weboberfläche.
Deniz Verified purchase
22.11.2025
Blitzschnell da, Paste knapp, Gamma @600 MHz stabil!
Leopold Verified purchase
18.11.2025
Ordered Friday evening, the parcel was in Utrecht on Tuesday and it went straight onto my Gamma that night. Strange shape for a Bitaxe cooler: barely higher than the stock block, but it overhangs the board on both sides, so measure your shelf first. Worth it though, at 575 MHz and 1200 mV the chip stays well under my 60 degree target while the Noctua hangs near the 25 percent floor. Hashrate close to 1.4 TH/s and quieter than stock, what a difference!
Maarten Verified purchase
02.11.2025
Kam in zwei Tagen, vier Heatpipes wirken Wunder!
Oskar Verified purchase
26.10.2025
Mit dem Serienkühler war bei 550 MHz Schluss jetzt läuft der Gamma mit 625 MHz und der Noctua bleibt dabei leise. Nach einer Woche unter meiner Zieltemperatur und keine Abschaltung.
Jochen Verified purchase
24.10.2025
Meine Frau hat beim Umbau gefragt, ob aus dem Gamma jetzt eine kleine Heizung wird, so sehen die vier Kupferröhrchen aus. Eher umgekehrt: Der Chip bleibt seit Dienstag so kühl, dass ich mich erstmals eine Frequenzstufe höher getraut habe, und die Hashrate ist spürbar gestiegen. Vorher hat der kleine Lüfter beim Fernsehen genervt, jetzt höre ich vom Wohnzimmerregal eher den Kühlschrank. Unser Großer wollte wissen, wo das Wasser durchläuft, und war enttäuscht, dass da keins ist. Drei Tage erst, aber ich bin begeistert!
Raphael Verified purchase
24.10.2025
Went from stock to 650 MHz at 1250 mV, chip still under the 60 degree target, fan nowhere near full. A month later the average sits close to 1.5 TH/s.
Dejan Verified purchase
23.10.2025
Flacher Riese! In zehn Minuten auf dem Nerdaxe.
Elias Verified purchase
22.10.2025
Measured properly before swapping: fan pinned at 35 percent, stock clock, chip in the low 60s on the original cooler. With the four heatpipes pulling the heat out into the wide fin block the same test lands in the mid 40s, so roughly fifteen degrees lower then before. Back on automatic with a 60 degree target the Noctua barely leaves the minimum speed I set, and the block and it's fins stay lukewarm under load. Two weeks only, but the numbers have not moved.
Ronan Verified purchase
22.10.2025
Take this as a mounting report rather than a verdict, the kit is three days old. My relationship with this hobby is odd anyway: the Gamma does its 1.2 TH/s, the electricity meter barely notices, and nobody here expects it to ever pay for itself. What I like is a small open piece of hardware I am allowed to modify, and this kit is exactly that. Getting the stock cooler off took longer than fitting the new one, the old paste had set like glue. Clean the chip, a rice grain of the included paste, bracket around it, four spring pins through the board, fan onto the 4-pin header. The block is low but much wider than the PCB, fine on an open desk, a problem in any box. Same 525 preset, target left at 60, and the Noctua settles far below where the stock 40 mm used to hover while the chip reads clearly cooler. My Nerdaxe Gamma is next, its firmware runs the fan flat out until you enable PID, so it needs this more. Sore point is the price: for a heatsink, a fan and a printed bracket it is not cheap, Noctua or not.
Márk Verified purchase
20.10.2025
Paket kam flott, mein Bitaxe verträgt eine Taktstufe mehr, ohne heiß zu werden. Die Paste im Set ist aber so knapp, dass der zweite Anlauf eng wurde, muss das sein?
Goran Verified purchase
20.10.2025
Plat mais large, et quelle galère ces pins.
Léa Verified purchase
19.10.2025
Noctua inaudible, mounting easy, but where's the manual?
Valentina Verified purchase
16.10.2025
Die vier Kupferrohre musste mir der Enkel erklären, montiert hab ich den Klotz mit den Steckpins dann selbst in einer Viertelstunde. Seitdem läuft die Kiste unauffällig, was mich fast ärgert.
Horst Verified purchase
03.10.2025
Am Gamma: 4 Heatpipes, flach, breit, Pins fummelig.
Silke Verified purchase
01.10.2025
La pasta térmica casi no me a llegado. El paquete tardó tres días y como novato me atreví a subir la frecuencia un escalon y el chip sigue fresco.
Héctor Verified purchase
30.09.2025
Installé sur un Bitaxe Gamma 601 il y a deux semaines, à la place du petit radiateur d'origine qui ne suivait plus dès que je touchais à la fréquence. Montage sans outil : ancien bloc retiré, puce nettoyée, une noisette de pâte, le support imprimé autour de l'ASIC, les quatre picots à ressort, la Noctua sur le connecteur 4 broches. Comptez un quart d'heure en prenant son temps. Le bloc est bas mais nettement plus large que la carte, à vérifier si le miner vit dans une niche. Côté chiffres, je suis passé du préréglage 490 à 575 MHz et la puce reste bien sous la cible de 60 degrés par défaut, là où l'ancien ventilateur montait sans arrêt en régime. Le tableau de bord tourne autour de 1,3 TH/s au lieu de 1,1 environ, et sur quinze jours la moyenne du pool suit. Le ventilateur de 60 mm reste proche de son minimum, je l'entends moins que mon NerdQaxe posé à côté, qui n'a droit à aucun kit de ce genre. Je n'irai pas plus haut, l'écart entre 575 et 650 ne vaut pas les watts, mais la marge est là pour l'été prochain.
Étienne Verified purchase
29.09.2025
Only catch: the fins stick out past the board edge. Same target temp, the 60 mm Noctua idles near the PWM floor where the stock 40 mm whined constantly.
Matej Verified purchase
31.07.2025
Das Einrasten der vier Pins war ein Geduldsspiel, beim letzen hätte ich fast zu fest gedrückt. Dafür ist die Chiptemperatur am Gamma bei gleicher Lüfterstufe grob zehn Grad runter.
Fabio Verified purchase
30.06.2025
Passt nicht für NerdQaxe
Ralf Verified purchase
30.06.2025
Eigentlich zu groß, funktioniert aber super.
Ricardo Verified purchase
26.06.2025
Besser geht es nicht
Artem Verified purchase
22.06.2025
Die Kühlleistung ist verrückt! Übertaktung bis 2 TH/s waren gar kein Problem
Thomas Verified purchase

Related guides

Setup, pool, cooling, power supply and sensible upgrades for your setup.

You might also like

ICE Tower Low Profile Kit

€69.00