Kupfer Kühlkörper
Small copper heatsinks for voltage regulators and hotspots on the board
Item no.: 75917 · Manufacturer: Bitaxe.de
- Copper heatsinks for VRMs and other hotspots
- A complement to ASIC cooling, not a replacement
- For Bitaxe and NerdQaxe boards
- Fitted in a few minutes
plus shipping · −5% with Bitcoin: €4.75
In stock · ships within 24 h
Product information
Copper heatsinks: cooling for the spots next to the ASIC
In home mining everyone watches the ASIC temperature – after all, it is the one on the dashboard. But an open board also gets warm elsewhere, above all at the voltage regulators that supply the chip. That is exactly where these small copper heatsinks come in.
Copper picks up the heat at the contact surface, spreads it across the fins and passes it to the air your fan is pushing over the board anyway. A point that heats up becomes an area that cools down – the cheapest adjustment in the setup.
Why heatsinks on the voltage regulators pay off
- Collect heat where it is created: the components next to the ASIC often have no cooling surface of their own as delivered.
- More even temperatures: buyers report that heat spreads better across the board after fitting them.
- Useful when overclocking: higher voltage means more losses at the regulators.
- The smallest upgrade: no rebuild, no new fan, no change in height.
A complement, not a replacement
Here is the honest limit: these heatsinks replace neither the fan nor the cooling on the ASIC. Without airflow over the board they achieve little, because the absorbed heat has to be carried away. They are the last percent on top – if the ASIC temperature is the problem, you need a bigger main heatsink.
Compatibility: Bitaxe and NerdQaxe setups
Because the heatsinks are seated rather than screwed down, they are not tied to a mounting pattern. They are intended for Bitaxe boards and compatible NerdQaxe setups – including devices such as the NerdQaxe++, which the large cooling kits do not fit. Putting those boards into operation is described in the NerdQaxe setup guide.
Who the copper heatsinks are for
For everyone who has their setup under control and wants the last few degrees: overclockers, 24/7 users and tinkerers who look closely at where their board gets warm.
If you are just starting out, this is the wrong place to start: a better main heatsink such as the ICE Tower Kit does far more.
What you need to fit them
Very little: switch the miner off, clean the target surface so it is free of grease, and seat the heatsink straight without tilting it. Buyers report the job is done in a few minutes. Make sure nothing touches neighbouring components and the airflow stays clear.
Accessories and sensible upgrades
- AXP60 Copper Pro if the ASIC on a Bitaxe Gamma or Nerdaxe Gaia needs more cooling mass.
- ICE Tower Low Profile kit as a main heatsink with four heatpipes for Bitaxe and Nerdaxe.
Ready to squeeze out the last few degrees?
If your miner runs, the main heatsink fits and you still want to operate your board more calmly, the copper heatsinks are the smallest sensible step – quickly fitted and reversible at any time.
Frequently asked questions about the Kupfer Kühlkörper
Do the copper heatsinks fit the Bitaxe Gamma?
Do they fit NerdQaxe boards as well?
Do the heatsinks replace the cooler on the ASIC?
Do they replace the fan?
Are such small parts worth it?
Where do the heatsinks go on the board?
How long does fitting take?
Can I use them together with a large heatsink?
What is the difference to the ICE Tower Kit?
What is the difference to the AXP60 Copper Pro?
Can I remove the heatsinks again?
Do they bring more hash rate?
Why buy from Bitaxe.de?
Free shipping from 200 €
Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.
Truly open source
Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.
CE, warranty & returns
Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.
Direct support
Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.
Customer reviews
4.9 / 5 · 27 reviews from customers who bought this product from us.
Kühlt und hält. Kann ich sehr empfehlen! Vielen Dank!
Mit isolierenden Pads auf den TPS546 und die Bauteile daneben gesetzt, die Reglertemperatur in AxeOS liegt seitdem fünf Grad tiefer. Ob dass so bleibt, mal sehen – einer saß zuerst schief.
Auf dem NerdQaxe++ passt von den großen Kühler-Kits sonst keins, deshalb sitzen die seit drei Monaten auf den Wandlern – für den Preis eines Kaffees die beste Ausgabe im Hobby bisher!
Beim Gamma mitbestelt, weil es kaum was kostet. Das Kupfer sieht neben dem Rest vom Board richtig edel aus, bei meinen Standardeinstellungen tut sich an der Temperatur allerdings nur wenig.
Hübsches Kupfer für Kleingeld, sieht nur keiner.
Ende Mai zusammen mit meinem ersten Gamma gekauft und erst mal in die Schublade gelegt, weil ich keine Ahnung hatte, wofür die kleinen Klötzchen gut sind. Verstanden habe ich es im Juli, als das Arbeitszimmer fast 30 Grad hatte und die Anzeige für den Spannungswandler stetig nach oben kletterte. Nach dem Aufsetzen ging die Temperatur ein paar Grad runter und blieb auch an den heißen Tagen dort. Zum ersten Mal selbst am Miner Hand angelegt, und es hat sofort geklappt!
Mein erster Miner läuft seit dem Sommer, und bis vor einem Monat wusste ich gar nicht, dass außer dem Chip noch etwas auf dem Board richtig warm wird. Dann habe ich auf der Übersichtsseite vom Miner die Temperatur vom Spannungswandler entdeckt, und die kam mir ziemlich hoch vor. Jetzt sitzen die kleinen Kupferdinger drauf, und der Wert ist um ein paar Grad gefallen. Macht richtig Spaß, dem Board beim Abkühlen zuzusehen, auch wenn ich vom Übertakten noch die Finger lasse!
Montati sui regolatori di tensione del mio Gamma a fine maggio, da allora il miner gira giorno e notte. La temperatura del regolatore nella dashboard è scesa di qualche grado e soprattutto resta più stabile quando in stanza fa caldo. Unica nota: col tempo il rame si è un po' scurito, ma è solo estetica. Per il resto, in quasi tre mesi non si sono mossi di un millimetro.
Gleich ein paar Grad weniger ich bin begeistert!
Seit Mai auf meinem Gamma, und die Klebepads halten immer noch, da ist nichts verrutscht. Mehr muss sowas auch nicht können.
Threw these in with my Gamma order since they cost next to nothing. A month later the regulator temperature in the dashboard sits about four degrees lower, roughly what I expected from a bit of passive copper. What I missed was a small sketch of where exactly they belong, so the first evening was guesswork around the regulator side of the board. Cleaning the spot properly took longer than the mounting itself. Good enough that the second Gamma gets them too.
Paar Grad weniger am Wandler, kostet fast nichts.
Ordered with the NerdQaxe since the big coolers don't fit it. Finding the voltage regulators took longer than sticking them on, but fine, that corner is merely warm now.
Gamma regulator was flirting with 90 °C at 1250 mV, reads 81 now with these on. Smartest few euros spent, and they come off again if I sell the board!
Bei 750 MHz und 1200 mV stand der Spannungsregler auf meinem Gamma im Dashboard um die 86 °C, der Chip entspannt bei 60. Nachdem ich den Overclocking-Ratgeber gelesen hatte, hab ich die Kupferteile zum zweiten Gamma einfach mitbestellt und auf dem ersten direkt auf die Wandler gesetzt: jetzt 78 °C bei gleichen 1,5 TH/s und rund 23 W. Der Lüfter regelt nur nach Chiptemperatur, deshalb hilft die passive Kühlung genau da, wo AxeOS nicht hinschaut. Für das Geld kaum was besseres zum Bastlen!
Für so wenig Geld hab ich selten so schnell eine Veränderung im Dashboard gesehen: drei Tage drauf, und die Wandler am Gamma laufen merklich kühler. Hätte ich früher machen sollen!
Board looks more finished with copper bits next to the ICE Tower, and the regulator runs a few degrees cooler. Nothing dramatic, but for that money I'll take it.
Mein erster Miner ist ein Bitaxe Gamma, und beim Bestellen habe ich die Kühlkörper schlicht übersehen. Eine Woche später dann doch nachbestellt, weil im Dashboard neben der Chiptemperatur noch ein zweiter Wert für den Spannungswandler steht und der mir im Sommer etwas hoch vorkam. Zweimal Versand bezahlt, aber das war mein eigener Fehler. Der Einbau selbst war unspektakulär: Miner aus, Stelle mit einem Tuch und etwas Alkohol sauber gemacht, Kühlkörper gerade aufgesetzt, fertig. Was mir gefehlt hat, war ein kleines Bild, welche Bauteile überhaupt gemeint sind; als Anfänger steht man vor so einer Platine und rät. Ich habe mich an dem orientiert, was nach einer Weile Betrieb am wärmsten war. Seit einer Woche läuft alles wie vorher, nur der Wert für den Wandler ist spürbar gesunken. Ob das am Ende etwas an der Lebensdauer ändert, kann ich natürlich nicht beurteilen. Für ein paar Euro war es mir den Versuch wert.
Pris au hasard avec ma commande vu que ça coûte presque rien, posé depuis l'hiver et ça fait joli. Aucune idée si ça change grand-chose, mais mon Bitaxe tourne tranquille.
Copper bling for my Bitaxe, looks the part.
Mitbestellt, paar Grad weniger, paar Fingerabdrücke mehr.
Sitzen seit fünf Tagen exakt da, wo sie hingehören: mit isolierenden Wärmeleitpads auf den Spannungswandlern vom GT, vorher Isopropanol drüber. Zum Miner dazubestellt, nur das Zuschneiden der Pads war fummelig.
Das Gamma sieht seit zwei Monaten aus wie ein kleines Steampunk-Bastelprojekt und die Spannungswandler laufen merklich entspannter. Beim Noctua damals einfach mit in den Warenkorb, kosten ja fast nichts!
sehen auf dem gamma richtig gut aus, fast schade dass es im regal steht. halten mit wärmeleitpads super, nur einer kam mit kratzer über die rippen an, beim preis verschmerzbar.
Quick add-on to my Gamma order, sticking nicely!
Kleine Kupferzähne fürs Board und das für weniger als ein Feierabendbier. Glanz nach zwei Wochen schon etwas matter dafür zeigt der Wandler im Dashbord weniger an.
Related guides
Setup, pool, cooling, power supply and sensible upgrades for your setup.
You might also like
ICE Tower Kit
AXP60 Copper Pro
Bitaxe Gamma Copper Pro | 1.5 TH/s