Bitaxe.de
Kupfer Kühlkörper Bitaxe2

Kupfer Kühlkörper

Small copper heatsinks for voltage regulators and hotspots on the board

Item no.: 75917 · Manufacturer: Bitaxe.de

  • Copper heatsinks for VRMs and other hotspots
  • A complement to ASIC cooling, not a replacement
  • For Bitaxe and NerdQaxe boards
  • Fitted in a few minutes
4,9 · 27 Reviews
€5.00 incl. VAT

plus shipping · −5% with Bitcoin: €4.75

In stock · ships within 24 h

Free shipping from 200 € Ships within 24 h 14-day right of withdrawal

Product information

Copper heatsinks: cooling for the spots next to the ASIC

In home mining everyone watches the ASIC temperature – after all, it is the one on the dashboard. But an open board also gets warm elsewhere, above all at the voltage regulators that supply the chip. That is exactly where these small copper heatsinks come in.

Copper picks up the heat at the contact surface, spreads it across the fins and passes it to the air your fan is pushing over the board anyway. A point that heats up becomes an area that cools down – the cheapest adjustment in the setup.

Why heatsinks on the voltage regulators pay off

  • Collect heat where it is created: the components next to the ASIC often have no cooling surface of their own as delivered.
  • More even temperatures: buyers report that heat spreads better across the board after fitting them.
  • Useful when overclocking: higher voltage means more losses at the regulators.
  • The smallest upgrade: no rebuild, no new fan, no change in height.

A complement, not a replacement

Here is the honest limit: these heatsinks replace neither the fan nor the cooling on the ASIC. Without airflow over the board they achieve little, because the absorbed heat has to be carried away. They are the last percent on top – if the ASIC temperature is the problem, you need a bigger main heatsink.

Compatibility: Bitaxe and NerdQaxe setups

Because the heatsinks are seated rather than screwed down, they are not tied to a mounting pattern. They are intended for Bitaxe boards and compatible NerdQaxe setups – including devices such as the NerdQaxe++, which the large cooling kits do not fit. Putting those boards into operation is described in the NerdQaxe setup guide.

Who the copper heatsinks are for

For everyone who has their setup under control and wants the last few degrees: overclockers, 24/7 users and tinkerers who look closely at where their board gets warm.

If you are just starting out, this is the wrong place to start: a better main heatsink such as the ICE Tower Kit does far more.

What you need to fit them

Very little: switch the miner off, clean the target surface so it is free of grease, and seat the heatsink straight without tilting it. Buyers report the job is done in a few minutes. Make sure nothing touches neighbouring components and the airflow stays clear.

Accessories and sensible upgrades

Ready to squeeze out the last few degrees?

If your miner runs, the main heatsink fits and you still want to operate your board more calmly, the copper heatsinks are the smallest sensible step – quickly fitted and reversible at any time.

Frequently asked questions about the Kupfer Kühlkörper

Do the copper heatsinks fit the Bitaxe Gamma?

Yes. They are seated on the components and intended for Bitaxe boards, including the Bitaxe Gamma. Just make sure there is enough free surface at the spot you have in mind.

Do they fit NerdQaxe boards as well?

Yes, they are designed for compatible NerdQaxe setups. That makes them one of the few cooling additions that also work for the NerdQaxe++ – the large ICE Tower kits do not fit there.

Do the heatsinks replace the cooler on the ASIC?

No. They are a complement for voltage regulators and other hotspots. The ASIC still needs its own heatsink.

Do they replace the fan?

No. Without airflow over the board they achieve very little, because the absorbed heat has to be carried away.

Are such small parts worth it?

If you overclock or your board runs under permanent load: yes. It is the cheapest cooling upgrade in the range. If your miner stays cool at factory settings, it is not necessary.

Where do the heatsinks go on the board?

On the components that get hottest under load – usually the voltage regulators next to the ASIC. Run the miner under load once and see where it gets warm.

How long does fitting take?

A few minutes. Most of it goes into cleaning the surface; after that you seat the heatsink straight and without tilting.

Can I use them together with a large heatsink?

Yes, that is exactly what they are for. They sit next to the main heatsink on the board and do not interfere with it as long as nothing collides.

What is the difference to the ICE Tower Kit?

The ICE Tower Kit replaces the main heatsink on the ASIC including the fan. The copper heatsinks take care of the remaining hotspots – one does not replace the other.

What is the difference to the AXP60 Copper Pro?

The AXP60 Copper Pro is a heatsink with 210 g of copper and a fan for the ASIC on the Bitaxe Gamma and Nerdaxe Gaia. These heatsinks are the small counterpart for the rest of the board and fit more models.

Can I remove the heatsinks again?

Yes. They are seated, not screwed or soldered – removal is possible if you pass the board on or rebuild it.

Do they bring more hash rate?

No, not on their own. They create thermal headroom; whether you turn that headroom into higher frequencies is up to your miner settings.

Why buy from Bitaxe.de?

Free shipping from 200 €

Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.

Truly open source

Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.

CE, warranty & returns

Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.

Direct support

Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.

Customer reviews

4.9 / 5 · 27 reviews from customers who bought this product from us.

All reviews
23.10.2026
Kühlt und hält. Kann ich sehr empfehlen! Vielen Dank!
Daniel Verified purchase
02.10.2026
Mit isolierenden Pads auf den TPS546 und die Bauteile daneben gesetzt, die Reglertemperatur in AxeOS liegt seitdem fünf Grad tiefer. Ob dass so bleibt, mal sehen – einer saß zuerst schief.
Moritz Verified purchase
28.09.2026
Auf dem NerdQaxe++ passt von den großen Kühler-Kits sonst keins, deshalb sitzen die seit drei Monaten auf den Wandlern – für den Preis eines Kaffees die beste Ausgabe im Hobby bisher!
Rolf Verified purchase
20.09.2026
Beim Gamma mitbestelt, weil es kaum was kostet. Das Kupfer sieht neben dem Rest vom Board richtig edel aus, bei meinen Standardeinstellungen tut sich an der Temperatur allerdings nur wenig.
Tobias Verified purchase
12.09.2026
Hübsches Kupfer für Kleingeld, sieht nur keiner.
Matteo Verified purchase
12.09.2026
Ende Mai zusammen mit meinem ersten Gamma gekauft und erst mal in die Schublade gelegt, weil ich keine Ahnung hatte, wofür die kleinen Klötzchen gut sind. Verstanden habe ich es im Juli, als das Arbeitszimmer fast 30 Grad hatte und die Anzeige für den Spannungswandler stetig nach oben kletterte. Nach dem Aufsetzen ging die Temperatur ein paar Grad runter und blieb auch an den heißen Tagen dort. Zum ersten Mal selbst am Miner Hand angelegt, und es hat sofort geklappt!
Jörg Verified purchase
Show all 27 reviews

Related guides

Setup, pool, cooling, power supply and sensible upgrades for your setup.

You might also like

Kupfer Kühlkörper

€5.00