Bitaxe.de
NerdQAxe Stand + Bitcoin miner Halterung 3

NerdQaxe Halterung

3D-printed stand made of CF-PLA for the NerdQaxe+ and NerdQaxe++

Item no.: NH10008NAH · Manufacturer: Bitaxe.de

  • Designed for the NerdQaxe+ and NerdQaxe++
  • CF-PLA with M3 brass threaded inserts
  • Matching screws included
  • A firm stand instead of a loose board among cables
4,8 · 45 Reviews
€19.00 incl. VAT

plus shipping · −5% with Bitcoin: €18.05

In stock · ships within 24 h

Choose variante

Free shipping from 200 € Ships within 24 h 14-day right of withdrawal

Product information

NerdQaxe mount: a secure stand for the NerdQaxe+ and NerdQaxe++

The NerdQaxe mount is a 3D-printed stand made of CF-PLA, carbon-reinforced PLA, designed for the NerdQaxe+ and NerdQaxe++. Instead of lying loose between power supply and cables, the miner sits in a fixed position – screwed down through embedded M3 brass threaded inserts, with the matching screws included.

The difference shows in daily use: the device no longer shifts when you unplug a cable, the ports stay reachable, and air reaches the heatsink freely.

Why a fixed mount makes sense

  • A defined position: the miner stays where you put it – even after the third cable swap.
  • Threads instead of plastic holes: the embedded M3 brass inserts keep holding when you loosen and tighten the screws repeatedly.
  • CF-PLA instead of a plain print: carbon-reinforced PLA is stiffer and more dimensionally stable than standard PLA and copes better with warm hardware.
  • Cables in order: power and network cables get a fixed route instead of wrapping around the board.

Does the mount fit your NerdQaxe?

The mount comes in one version each for the NerdQaxe+ and NerdQaxe++; you pick the right one before ordering. It is not intended for other devices – the NerdOctaxe and the Bitaxe models have a different form factor.

One note from the reviews that we would rather give upfront: some NerdQaxe units already come with a simple stand. So take a quick look in your box before ordering. This mount is the sturdier solution, but it is not necessary in every setup.

Who the NerdQaxe mount is for

For everyone running their miner in plain sight: on a desk, on a shelf or in a homelab rack. If you place several NerdQaxe next to each other, the benefit doubles, because every device keeps its own spot and spacing.

It is less suitable if what you actually want is cooling or a case. The mount makes your miner neither quieter nor cooler – the NerdQaxe Performance Case with its open design and fan mounts is made for that.

What you need to fit it

Mount and screws come together, so you only need a screwdriver and a few minutes – ideally while setting up the NerdQaxe. Two points from practice: the first fit is a little tight – press evenly rather than forcing it. And with thicker cables, decide on the cable route before screwing everything down.

Accessories and sensible upgrades

  • NerdQaxe++, if the mount is meant for a second device in your setup.
  • OLED display as a spare part if your NerdQaxe display is damaged.
  • Mining accessories for fans, cooling and the rest of the build.

Ready for a tidy NerdQaxe setup?

A stand is not a spectacular upgrade, but it decides whether your miner looks like a device or like a temporary arrangement. You get a firm stand, clean cable routing and a setup worth showing.

Frequently asked questions about the NerdQaxe Halterung

Does the mount fit the NerdQaxe++?

Yes. There is a version for the NerdQaxe++ and one for the NerdQaxe+. Pick the variant that matches your device before ordering.

Does the mount fit a Bitaxe as well?

No, it is designed exclusively for the NerdQaxe+ and NerdQaxe++. The Bitaxe Gamma comes with a 3D-printed stand in the box anyway.

Does my NerdQaxe already include a stand?

Possibly – one customer found exactly that afterwards. Check your device’s box. This mount is the sturdier variant with brass threads, but you do not necessarily need two of them.

What material is the mount made of?

CF-PLA, carbon-reinforced PLA. The material is stiffer and more dimensionally stable than plain PLA. M3 brass threaded inserts are embedded for the screws.

Are screws included?

Yes, matching M3 screws are included. The only tool you need is a screwdriver.

Does the mount make my miner quieter or cooler?

No. It changes neither the fan nor the heatsink. Indirectly a free-standing position helps airflow, but measurable cooling only comes from more surface or a better fan from the cooling category.

What is the difference between the mount and the Performance Case?

The mount holds the miner up, nothing more. The NerdQaxe Performance Case is a three-part enclosure with cable channels and two prepared 60 mm fan mounts at the rear. If airflow is your concern, the case is the right choice.

How involved is the assembly?

It takes a few minutes. On first fit the board sits a little tight; after that it holds securely. No force required.

Do the ports stay reachable?

Yes, that is the point of the design: power connector and cables stay accessible without lifting the miner.

Can I place several miners next to each other?

Yes, each mount holds its own device. Leave enough space between the miners so every heatsink gets free airflow.

How do I know whether I have a NerdQaxe+ or a NerdQaxe++?

The model name is printed on the board and shown in your miner’s web interface, which you reach through the setup guide. If you are unsure, compare with the product page of the NerdQaxe++ before choosing the variant.

Why buy from Bitaxe.de?

Free shipping from 200 €

Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.

Truly open source

Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.

CE, warranty & returns

Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.

Direct support

Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.

Customer reviews

4.8 / 5 · 45 reviews from customers who bought this product from us.

All reviews
05.10.2026
Stph Verified purchase
18.09.2026
The CF-PLA print has a uniform matte finish, and after two weeks with the ++ on it there is no flex at all.
Bas Verified purchase
17.09.2026
schrauben hab ich schon zweimal wieder gelöst, weil das dicke netzteilkabel erst beim dritten versuch so lag, wie ich's haben wollte, und die messing-einsätze nehmen einem das null übel! der ++ sitzt satt, egal wie oft ich an den steckern rumfummle, kein vergleich zu vorher, als das board lose rumlag! nur wenn ich die tasten am display drücke, federt das ganze minimal nach, da dürfte der ständer einen tick steifer sein.
Bernd Verified purchase
16.09.2026
ordered it back in march and it reached porto three days later, padded like it was made of glass. six months on, the ++ is still screwed down tight and nothing has worked loose. temps didn't change and i never expected them to, but the underside of the board finally gets some air too. pointed the ++ at the new bitaxe pool last week, and on this stand it at least looks the part while it hunts.
Rui Verified purchase
14.09.2026
Bombenfest verschraubt und unterm Board zieht Luft durch
Lenny Verified purchase
03.09.2026
Back in July the NerdQaxe++, my first and only miner, lay directly on a shelf of the bookcase in our hallway. It worked, but it looked like a circuit board somebody had forgotten there, and the cables hung down over the books. With the holder it is a different picture. The miner now stands clear of the books with room all around it, nothing in the way of the airflow, and the cables run neatly to the back instead of across the front. Visitors have stopped asking whether it is part of the internet router. The print itself is neat. My neighbour's son, who owns a 3D printer and has strong opinions about other people's prints, turned it over in his hands for a while, looked closely at the layer lines and the screw holes, and handed it back with a slightly disappointed 'clean'. After a month it simply belongs to the bookcase, and I enjoy looking at it.
Nikos Verified purchase
Show all 45 reviews

Related guides

Setup, pool, cooling, power supply and sensible upgrades for your setup.

You might also like

NerdQaxe Halterung

€19.00