NerdQaxe Halterung
3D-printed stand made of CF-PLA for the NerdQaxe+ and NerdQaxe++
Item no.: NH10008NAH · Manufacturer: Bitaxe.de
- Designed for the NerdQaxe+ and NerdQaxe++
- CF-PLA with M3 brass threaded inserts
- Matching screws included
- A firm stand instead of a loose board among cables
plus shipping · −5% with Bitcoin: €18.05
In stock · ships within 24 h
Product information
NerdQaxe mount: a secure stand for the NerdQaxe+ and NerdQaxe++
The NerdQaxe mount is a 3D-printed stand made of CF-PLA, carbon-reinforced PLA, designed for the NerdQaxe+ and NerdQaxe++. Instead of lying loose between power supply and cables, the miner sits in a fixed position – screwed down through embedded M3 brass threaded inserts, with the matching screws included.
The difference shows in daily use: the device no longer shifts when you unplug a cable, the ports stay reachable, and air reaches the heatsink freely.
Why a fixed mount makes sense
- A defined position: the miner stays where you put it – even after the third cable swap.
- Threads instead of plastic holes: the embedded M3 brass inserts keep holding when you loosen and tighten the screws repeatedly.
- CF-PLA instead of a plain print: carbon-reinforced PLA is stiffer and more dimensionally stable than standard PLA and copes better with warm hardware.
- Cables in order: power and network cables get a fixed route instead of wrapping around the board.
Does the mount fit your NerdQaxe?
The mount comes in one version each for the NerdQaxe+ and NerdQaxe++; you pick the right one before ordering. It is not intended for other devices – the NerdOctaxe and the Bitaxe models have a different form factor.
One note from the reviews that we would rather give upfront: some NerdQaxe units already come with a simple stand. So take a quick look in your box before ordering. This mount is the sturdier solution, but it is not necessary in every setup.
Who the NerdQaxe mount is for
For everyone running their miner in plain sight: on a desk, on a shelf or in a homelab rack. If you place several NerdQaxe next to each other, the benefit doubles, because every device keeps its own spot and spacing.
It is less suitable if what you actually want is cooling or a case. The mount makes your miner neither quieter nor cooler – the NerdQaxe Performance Case with its open design and fan mounts is made for that.
What you need to fit it
Mount and screws come together, so you only need a screwdriver and a few minutes – ideally while setting up the NerdQaxe. Two points from practice: the first fit is a little tight – press evenly rather than forcing it. And with thicker cables, decide on the cable route before screwing everything down.
Accessories and sensible upgrades
- NerdQaxe++, if the mount is meant for a second device in your setup.
- OLED display as a spare part if your NerdQaxe display is damaged.
- Mining accessories for fans, cooling and the rest of the build.
Ready for a tidy NerdQaxe setup?
A stand is not a spectacular upgrade, but it decides whether your miner looks like a device or like a temporary arrangement. You get a firm stand, clean cable routing and a setup worth showing.
Frequently asked questions about the NerdQaxe Halterung
Does the mount fit the NerdQaxe++?
Does the mount fit a Bitaxe as well?
Does my NerdQaxe already include a stand?
What material is the mount made of?
Are screws included?
Does the mount make my miner quieter or cooler?
What is the difference between the mount and the Performance Case?
How involved is the assembly?
Do the ports stay reachable?
Can I place several miners next to each other?
How do I know whether I have a NerdQaxe+ or a NerdQaxe++?
Why buy from Bitaxe.de?
Free shipping from 200 €
Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.
Truly open source
Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.
CE, warranty & returns
Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.
Direct support
Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.
Customer reviews
4.8 / 5 · 45 reviews from customers who bought this product from us.
The CF-PLA print has a uniform matte finish, and after two weeks with the ++ on it there is no flex at all.
schrauben hab ich schon zweimal wieder gelöst, weil das dicke netzteilkabel erst beim dritten versuch so lag, wie ich's haben wollte, und die messing-einsätze nehmen einem das null übel! der ++ sitzt satt, egal wie oft ich an den steckern rumfummle, kein vergleich zu vorher, als das board lose rumlag! nur wenn ich die tasten am display drücke, federt das ganze minimal nach, da dürfte der ständer einen tick steifer sein.
ordered it back in march and it reached porto three days later, padded like it was made of glass. six months on, the ++ is still screwed down tight and nothing has worked loose. temps didn't change and i never expected them to, but the underside of the board finally gets some air too. pointed the ++ at the new bitaxe pool last week, and on this stand it at least looks the part while it hunts.
Bombenfest verschraubt und unterm Board zieht Luft durch
Back in July the NerdQaxe++, my first and only miner, lay directly on a shelf of the bookcase in our hallway. It worked, but it looked like a circuit board somebody had forgotten there, and the cables hung down over the books. With the holder it is a different picture. The miner now stands clear of the books with room all around it, nothing in the way of the airflow, and the cables run neatly to the back instead of across the front. Visitors have stopped asking whether it is part of the internet router. The print itself is neat. My neighbour's son, who owns a 3D printer and has strong opinions about other people's prints, turned it over in his hands for a while, looked closely at the layer lines and the screw holes, and handed it back with a slightly disappointed 'clean'. After a month it simply belongs to the bookcase, and I enjoy looking at it.
jetzt endlich fotogen genug für den setup-thread im forum. board sitzt plan, nach acht wochen musste keine schraube nachgezogen werden, und an die anschlüsse komm ich trotzdem bequem ran.
Mijn vriendin vond de NerdQaxe++ eerst te rommelig voor de woonkamer, maar op deze houder mag hij ineens naast de tv blijven hashen!
Der ++ sitzt passgenau auf der Halterung, und zwischen NAS und Switch fällt die schlichte Form kaum auf, was ich durchaus als Kompliment meine.
So hübsch gedruckt, und so schön luftig!
Von den ganzen gedruckten Ständern und Halterungen, die sich bei mir für die Miner angesammelt haben, ist das hier der sauberste Druck. Keine Fädchen, keine Blobs, die Oberfläche gleichmäßig, und die Schrauben gingen ohne Gefummel rein. Der ++ hasht weiter wie gehabt auf public-pool, sitzt jetzt aber fest und knarzt nicht, wenn man mal dran wackelt. Zur Haltbarkeit kann ich nach fünf Tagen natürlich noch nix sagen.
Sunday evening order, Thursday delivery to Utrecht, not bad for a parcel crossing the border. Until then my NerdQaxe++ sat right on the windowsill with its fan a few centimetres from the curtain, because as a beginner I simply had not thought about airflow. On the holder there is open space around it, the curtain stays where it belongs, and I can reach the cables without moving the miner.
Lieferung flott, passende Schrauben im Tütchen, und seit zwei Monaten sitzt der ++ darauf im Kellerregal, wo er stur seine 78 W zieht und knapp unter 5 TH/s abliefert.
Das Paket war tatsächlich schneller da als die Filamentrolle, die ich am selben Abend bei einem anderen Shop bestellt hatte! Ausgepackt, gegen das Licht gehalten und sofort begeistert: Z-Naht sauber in eine Innenkante gelegt, Ecken scharf, Schraublöcher rund statt leicht oval, keine Pickel auf den Flächen. Die Schichtlinien sind so gleichmäßig, dass man sie nur im Streiflicht wirklich sieht. Genommen habe ich zwei Stück für meine beiden ++, die jetzt mit einer Handbreit Abstand im Homelab-Regal stehen. Jeder 92er Lüfter bekommt von allen Seiten Luft, nichts steht mehr im Weg. Die ASIC-Temperaturen im Dashboard sind trotzdem dieselben wie vorher, und das hatte ich auch nicht anders erwartet, ein Ständer ist eben kein Kühler. Der erste Einbau war etwas fummelig, weil die Passung knapp ist, Gewalt brauchte es aber keine. Zehn Tage erst, aber so ordentlich sah meine Mining-Ecke noch nie aus!
Druckrillen gratis, Durchzug inklusive, Versand zackig.
Fan has room to breathe now and its been holding my NerdQaxe++ steady for two months, arrived quicker than I expected too, would buy again.
Le support épouse le PCB du ++ au millimètre, rien à forcer. Couches régulières, pas un fil, pas une bavure. Posé à côté de l'écran, câble d'alim enfin rangé, le mineur a vraiment de la gueule sur le bureau ! Il tourne toujours à 600 MHz, logique, un pied ne change rien au hashrate, mais il est autrement plus joli à regarder !
Blitzsauber gedruckt, bin begeistert!
Ruckzuck geliefert, festgeschraubt, kein Kippeln mehr und drumherum genug Platz für Luft – ein echter Sprung gegenüber dem einfachen Ständer aus dem ++-Karton!
I got the NerdQaxe++ as a birthday present in October, and since I am completely new to mining, the names confused me at first: Bitaxe, Nerdaxe, NerdQaxe, plus signs everywhere. So before ordering the holder I compared the name printed on the board with the product page, twice. It matched, and the ++ sat on it as if it had been made for it, which of course it was. Mounting went fine, the screws are included and an ordinary screwdriver was enough. Three months later it still stands on the bookshelf in my study exactly where I put it and has not shifted once, not even when I dust around it. If I had to change one thing, it would be the colour. It does not really go with the light wood of the shelf, and I did not see a choice of colours when ordering. For something I hardly notice any more, that is a small point.
Mechanisch passt das: Board verschraubt, die Schrauben greifen sauber, und der ++ rührt sich nicht, auch wenn man mal dagegen stößt. Der Lüfter regelt bei mir per PID, da vibiert auch nix mit. Was mich nach vier Wochen aber immer noch stört, ist die Farbe, im 19-Zoll-Rack wirkt das neben dem restlichen Equipment wie ein Fremdkörper. Schade, das es da keine Auswahl gibt.
Für mich als blutigen Anfänger war die größte Sorge gar nicht das Einrichten, sondern dass mir der Miner irgendwann vom Sideboard kippt. Mit dieser Halterung ist das Thema durch! Der NerdQaxe++ ist festgeschraubt und hat sich seit Oktober keinen Millimeter bewegt, obwohl unser Kater regelmäßig da oben herumturnt. Sogar den Netzteilstecker kann ich ziehen, ohne das Gerät mit der anderen Hand festzuhalten. Bin echt froh, dass ich die gleich mitbestellt habe.
Ordentlicher Druck, keine Grate, hält seit Wochen.
Sachlich betrachtet ist es ein gedruckter Ständer mit Schraublöchern, mehr nicht, aber genau das hat gefehlt. Der NerdQaxe++ steht jetzt neben meinem Gamma im Regal, und das Ganze wirkt zum ersten Mal wie ein fertiges Setup und nicht wie eine Bastellösung. Die Druckqualität ist gleichmäßig, die Kanten sind glatt, nirgends ein Rest vom Stützmaterial. Nach einem Monat sitzt der Miner noch genauso stramm wie am ersten Tag. Die Kabel laufen jetzt hinten weg statt quer über den Tisch.
Luft kommt jetzt auch unters Board, gut so.
Als Rentner und Neuling beim Mining wollte ich nur, dass der Miner nicht mehr lose auf der Kommode liegt. Trotz Vorweihnachtsrummel war das Päckchen vom selben Shop wie der Miner nach zwei Tagen da, Schrauben lagen bei, und mit dem Schraubenzieher aus der Küchenschublade war alles in zehn Minuten fest. Der Druck fühlt sich stabil an, nichts biegt sich, keine scharfen Kanten, und die Schrauben griffen sofort. Mehr kann ich nach drei Tagen nicht sagen, aber er steht, und darum ging es.
Endlich steht der ++ ordentlich, Kühler frei angeströmt!
schnell da, passt auf den ++, steht. fertig.
I'm completely new to mining, and I almost skipped this because my NerdQaxe++ already came with a small printed stand. Glad I didn't! On that one the board always felt a bit loose, and while I was still figuring out the pool settings I kept worrying I'd knock it over. Now it's screwed down and the whole thing feels like one solid piece. Getting the board in the first time was a snug fit and I was nervous about pressing too hard, but pushing evenly did the trick, and you can tell the ++ version was made for exactly this board. The print looks good from a normal distance and feels sturdy in the hand. Up close you can see the fine ridges of the individual layers, which bugged me for about a day before I stopped noticing. It now sits on the shelf mining on public-pool at around 4.8 TH/s, and I catch myself glancing at the little screen every time I walk past.
Before this holder my NerdQaxe++ slid around the desk every time I touched a cable, and in the first weeks that was often. Now it stays put and the board is not lying flat on the desk anymore, so air can reach the underside as well. Temperatures did not change, but I did not expect that from a stand. The ++ version matched the board without fiddling, screw holes lined up, screws were in the bag, nothing else to buy.
Makes the whole thing look like an actual device on my shelf instead of a bare board with cables hanging out, four months now and still happy with it.
Solid stand, layer lines a bit too visible.
Love the airflow, fits the ++, wobbles though!
Mein Entschluss, Geld für einen Ständer auszugeben, hat vier Wochen gedauert, die Lieferung danach zwei Tage. Der Druck ist so sauber, keine Fäden, keine Kleckse, dass der ++ darauf jetzt fast ungepflegt wirkt, was allerdings auch am Staub auf seinem Kühler liegen könnte. Er schiebt seine 4,8 TH/s weiter brav Richtung Pool, nur der Block lässt auf sich warten. Am Ständer liegt das vermutlich nicht.
Wer selbst ab und zu am Slicer sitzt, schaut bei gedruckten Teilen genauer hin, und dieser Ständer hält dem Blick locker stand! Die Überhänge sind sauber, die Stellen, an denen Stützmaterial saß, muss man regelrecht suchen, und die Maße stimmen so genau, dass der ++ beim ersten Versuch draufging. Seit Mitte Juni läuft er darauf bei 600 MHz mit knapp 4,9 TH/s, der 92er regelt per PID, und trotz der Wärme direkt am Kühlkörper hat sich nichts verzogen oder gelockert. Richtig ordentliche Arbeit für ein Zubehörteil!
Zwei Tage nach der Bestellung vor der Tür. Druck sauber, nichts nachzuarbeiten, und der ++ sitzt seit einer Woche fest, ohne beim Umstecken zu wandern.
Tengo dos NerdQaxe++ en la misma balda y antes estaban tumbados, muy juntos y con la balda de arriba a pocos centímetros de los ventiladores. Con un soporte para cada uno quedan de pie, separados un palmo, y el aire entra y sale sin tropezar con nada. Después de un mes no he visto holguras ni deformaciones en ninguno de los dos. Si llega un tercer minero, pediré otro soporte.
Stojánek jsem si přiobjednal pár dní po svém prvním mineru a nadšení mě zatím nepřešlo. NerdQaxe++ teď stojí na botníku v předsíni a i když do botníku občas narazí robotický vysavač, nehne se ani o kousek. Tisk je povedený, povrch je hladký a nikde nevisí žádné vlásky. Méně nadšený jsem z ceny: za pár gramů filamentu mi to přijde docela dost peněz. To je ale opravdu jediná výtka.
Sieht jetzt richtig aufgeräumt aus auf dem Schreibtisch.
Eigentlich kauf ich ungern Plastikkram dazu. Der hier hat sich aber gelohnt: Druck ohne Fehler, der ++ steht seit gut einem Monat wie angewachsen, und im Regal schau ich ihn inzwischen sogar gern an.
Ce qui me plaît le plus, c'est un détail : je peux enfin appuyer sur les boutons de l'écran pour faire défiler les pages sans que tout le NerdQaxe++ recule ou penche ! Avant, je le retenais d'une main et j'appuyais de l'autre, pas très glorieux. Maintenant il tient debout sur l'étagère du bureau, bien droit, vissé sur son support. L'impression est soignée : les trous tombent pile en face de ceux de la carte et la pièce est rigide, elle ne se tord pas quand on serre les vis. Au toucher, la surface est régulière. Ça fait trois semaines qu'il tourne dessus jour et nuit et rien n'a pris de jeu. Le ventilateur de 92 mm garde de la place pour respirer, c'était ma seule petite crainte avant de commander. Je suis ravi, et l'étagère a l'air nettement plus rangée !
Impressão limpa, o ++ encaixou à primeira. Raro.
Macht was sie soll.
Die Halterung kam zusammen mit dem ++ und ist jetzt seit einer Woche im Einsatz. Im Regal macht mein ++ damit ne richtig gute Figur und steht satt auf dem Brett, ein Kumpel hat beim Grilen schon gefragt, wo man sowas herbekommt. Die Oberfläche ist gleichmäßig, keine Nasen oder Pickel vom Druck, und selbst die Unterseite ist so sauber wie die Sichtseite. Kleiner Minuspunkt: tippt man oben gegen den Kühler, wippt das ganze ein bisschen, im normalen Betrieb merkt man davon aber nix.
Ich habe eine bestellt, dann gemerkt das beim Miner schon eine Halterung dabei war... Trotzdem gut!
Related guides
Setup, pool, cooling, power supply and sensible upgrades for your setup.
You might also like
NerdQaxe Performance Case
NerdQaxe++ Rev7 | 4.8 TH/s
NerdQaxe++ Hydro | 6 TH/s