NerdQaxe Performance Case
Open three-part PLA case for the NerdQaxe – airflow instead of heat build-up
Item no.: 47415 · Manufacturer: Bitaxe.de
- Three-part PLA case for the NerdQaxe series
- Open design for high airflow
- Rear prepared for 2 × 60 mm fans
- Side cable channels, M3 screws included
plus shipping · −5% with Bitcoin: €27.55
In stock · ships within 24 h
Product information
NerdQaxe Performance Case: an open enclosure with clear airflow
The NerdQaxe Performance Case is a three-part PLA enclosure designed for the NerdQaxe. The three parts are screwed into one unit with the included M3 screws: the miner sits firmly, the ports stay reachable and the build stands as a single piece on a desk, shelf or in a rack.
The difference to a closed case is deliberate. Large openings at the front and sides let warm air escape instead of letting it collect around the heatsink – and there is room for two additional fans at the rear.
Why an open case?
- Air instead of a wall: the large openings prevent the ASIC’s heat from gathering inside the enclosure.
- A second cooling layer: 2 × 60 mm fans can be fitted at the rear, for example the Noctua NF-A6x15.
- Cables in channels: side cable channels route power and fan cables without laying them across the airflow.
- A firm fit: three precisely fitting parts and M3 screws instead of loosely stacked plates.
What the case can do – and what it cannot
An open enclosure improves airflow, but it insulates nothing. If your NerdQaxe is too loud for you, the case will not change that; that comes down to fan curve and fan choice.
The two 60 mm rear fans are not included. Plan for them if you run higher performance profiles permanently. At stock settings many setups get along without extra fans – as described by customers who run the case exactly that way.
Who the Performance Case is for
For continuous operation and for everyone who wants to build their NerdQaxe properly into their setup: a firm build, routed cables, free ports. And for everyone who adjusts frequency and voltage and needs temperature headroom for it.
It is less of a fit if all you need is a stand. Then the NerdQaxe mount is the cheaper and simpler solution. And if you are after silence, the money is better spent on fans and cooling surface.
What you need to assemble it
Case and M3 screws come in the box, and you need a screwdriver. The easiest moment is right when setting up the NerdQaxe. Take a few minutes and lay the cables into the channels before tightening the last part – otherwise you will be redoing it. Optionally add two 60 mm fans and their power supply.
Accessories and sensible upgrades
- Cooling: heatsinks and fans that absorb the heat before the case carries it away.
- Mining accessories for cables, mounts and spare parts around the build.
Ready for your NerdQaxe performance setup?
The Performance Case is the choice when your NerdQaxe runs around the clock and you want to give it air, order and a fixed place: an enclosure that lets heat through instead of locking it in.
Frequently asked questions about the NerdQaxe Performance Case
Does the Performance Case fit every NerdQaxe?
Are fans included?
Which fans fit the rear?
Will my NerdQaxe be quieter in the case?
Will the miner run cooler in the case?
What is the difference between the case and the NerdQaxe mount?
How long does assembly take?
Do ports and display stay reachable?
What material is the case made of?
Do I need the case if I want to overclock?
Does the case fit a Bitaxe as well?
Why buy from Bitaxe.de?
Free shipping from 200 €
Free shipping to almost every EU country from 200 €, shipping to the EU and Switzerland with UPS and a tracking link. Items in stock leave within 24 hours, with no customs surprises inside the EU.
Truly open source
Bitaxe, Nerdaxe, NerdQaxe & co. are open hardware running open firmware (AxeOS or NerdOS): you set pool, clock and voltage yourself. No cloud account, no vendor lock-in, no black box.
CE, warranty & returns
Every product carries the CE marking. Plus statutory warranty and a 14-day right of withdrawal for a safe order. If something is not right, we find a solution with you, person to person.
Direct support
Questions about setup, pool, firmware or your order? By email or Telegram you get help from someone who runs these devices themselves, in English or German, beginners welcome.
Customer reviews
4.9 / 5 · 30 reviews from customers who bought this product from us.
Hab das Case nur gekauft, weil der NerdQaxe neben dem Node so verloren aussah, jetzt passt das Bild im Regal. Morgens beim Kaffee kurz hingeschaut, mehr muss es nicht können.
Mit OSM-OS und mehr Takt bleibt der Chip unter 65 Grad, die Abwärme vom 92er kommt durch die offenen Seiten weg. Optisch wird aus dem Bastelprojekt ein richtiges Gerät.
Wow, jetzt ist der NerdQaxe ein echter Hingucker! Durch die großen Aussparungen sieht man Kühlkörper und Lüfter arbeiten, das hat was von einem offenen Gaming-PC, und so darf er gern im Regal stehen. Wer die Hand seitlich dranhält, spürt, wie die warme Luft ungehindert abzieht, da bleibt nichts hängen. Nach zwei Wochen freue ich mich immer noch über den Anblick, wenn ich ins Zimmer komme. Der Besuch am Wochenende musste sich das gleich von allen Seiten anschauen!
Mainly bought it for the two 60mm slots at the back... Noctuas are on order, plan is to push the clock a bit once they're in.
Quick build, one print edge a bit rough.
I wanted something that gives the heatsink plenty of air and keeps stray fingers and cables off the board. This case manages both. It's more skeleton than box, chip temps haven't moved at all, and the board is shielded from the usual desk clutter alot better than before. Price is the sticking point for me: it's a printed part, and I sat on the order for two weeks before clicking buy. Still glad I got it, it just isn't cheap.
Mein NerdQaxe sieht jetzt aus, als hätte ihn jemand mit Absicht so hingestellt und nicht einfach vergessen. Das Display guckt vorne raus, Best Diff bleibt trotzdem unverändert ernüchternd.
Nebenbei beim Serienschauen zusammengeschraubt, und im Rack wirkt der Qaxe jetzt wie aus einem Guss. Die beiden 60er für die Rückseite musste ich nachbestellen, ein Set mit Lüftern wäre nett gewesen.
Zusammengeschraubt, Platine endlcih nicht mehr nackt, passt.
Anzeige gut lesbar, Board musste ich ordentlich reindrücken.
It took me maybe a quarter of an hour with a small screwdriver (the one from the kitchen drawer). Three printed parts, a handful of M3 screws, and the power cable goes into the side channel before the last part is screwed on, which I had read beforehand, so no second attempt was needed. The miner does not move now, before it was simply standing on its stock stand. Too early to say much about temperatures, it has only been running since Tuesday.
Montato in pausa pranzo: basta un cacciavite e un po' di pazienza per sistemare il cavo nella canalina. Da un paio di mesi sposto il NerdQaxe++ con una mano sola quando pulisco la scrivania, comodissimo!
Die Platine liegt nicht mehr offen auf dem Schreibtisch, und hinten sind zwei 60-mm-Plätze frei, falls ich später höher takten will. Sitzt fest, wackelt nichts.
Montaje fácil, mucho aire y placa protejida. Genial!
The sides are mostly open, so the 92 mm fan gets all the air it wants, and my hand no longer brushes the components when I reach behind it for a plug.
Endlich kann ich den Miner anfassen ohne Herzklopfen.
Bei mir laufen drei kleine Miner auf dem Dachboden, und der NerdQaxe++ war der einzige mit komplett freiliegender Platine, was der Kater als Einladung verstand. Seit April steckt er im Performance Case, drei Teile verschraubt, Platine hinter Plastik, und die Katzenhaare landen am Gehäuse statt auf den Bauteilen. Hinten drehen zwei 60er mit, weil es unterm Dach im Juli brutal warm wird; den Strom dafür muss man sich selbst organisieren, das sagt der Shop aber auch so. Stromzähler dreht trotzdem fleißig, anderes Thema.
Zwei Noctuas hinten rein, seit Mai unauffällig.
Wärme raus, Platine eingefasst, mehr wollte ich nicht.
Took me longer to find a screwdriver than to put this together! Three printed parts, a few screws, and the NerdQaxe++ sits in there like it never belonged on the little stand it came with. Display and USB-C cutouts line up exactly, and the side channels swallow the thick power cable so nothing dangles infront of the fan anymore. Its standing next to my Gamma now and the two of them finally look like they belong to the same person. Twenty minutes, coffee included.
Der NerdQaxe++ steht im Wohnzimmerregal zwischen den Kochbüchern, bis vor ein paar Tagen sah das aus wie eine Elektronik-Baustelle mit Kabelsalat. Jetzt sitzt er im dreiteiligen Case, das Display mit Hashrate und Temperatur zeigt nach vorne, und meine Frau hat zum ersten Mal nicht gefragt, wann der Miner in den Keller zieht! Die Kinder lesen morgens die Best Difficulty ab wie den Wetterbericht. Zusammengebaut war es am Samstag in einer halben Stunde, und seitdem fragt kein Besuch mehr, ob das ein kaputter Router ist.
Dass man für so einen Miner noch ein Gehäuse extra kauft, fand ich erst übertrieben. Jetzt ist die Platine eingerahmt, der Staubsauger stößt nirgends mehr an, und das Zusammenschrauben hat auch ohne Technikverstand geklappt.
Für die zwei Lüfterplätze hinten hatte ich erst einen 40er aus der Restekiste probiert, keine Chance, die Bohrungen sind für 60 mm. Zusammengebaut war es flott, nur beim Preis für gedruckten Kunststoff musste ich schlucken.
Hatte Angst, das Ding falsch zusammenzuschrauben, war aber nach einer Viertelstunde fertig. Das Display mit den Zahlen schaut vorne raus und auf der Kommode sieht es richtig ordentlich aus!
What finally made me order this: the PSU cable caught on my chair and the NerdQaxe++ nearly went off the desk, stand included. Not again. Putting the case together was fine, though it took me longer than a few minutes because I kept holding the parts the wrong way round. Now the board is framed on every side, nothing snags on it, and the power lead sits in its channel instead of trailing across the floor. Should have bought it weeks ago.
Kabelkanal eng, dafür Display sichtbar und zwei Lüfterslots!
Ich takte den NerdQaxe++ ein Stück über Werkseinstellung und wollte Spielraum bei der Kühlung, also das Case mit Option auf zwei 60-mm-Lüfter hinten. Zusammenbau ging schneller als das Auspacken, und das Ganze steht bombenfest im Rack neben dem Switch! Einziger Haken: die seitlichen Kabelkanäle sind richtig knapp, das Netzteilkabel musste ich zweimal neu einlegen, bevor das letzte Teil zuging. Dafür sitzt die Platine jetzt sauber im Rahmen und wirkt da nicht mehr wie ein Fremdkörper.
Bello e rapido da montare ma canaline strettissime.
Alles bestens!
Das Case ist echt super. Schneller leichter Einbau in ein paar Minuten. Die Temperaturen sind perfekt.
Related guides
Setup, pool, cooling, power supply and sensible upgrades for your setup.
You might also like
Noctua NF-A6x15 Silent Fan
NerdQaxe Halterung
NerdQaxe++ Rev7 | 4.8 TH/s